The LPC1114 Starter Kit produced by Embest is a brand new and low cost full-featured evaluation kit based on the NXP LPC1100 Cortex-M0 Series processor. The target board works at up to 50MHz, supports the RS485 Mode and integrates power management Unit (PMU). In addition, the board features a wide range of peripherals, including UART interface, eight channels 10bit ADC, tow 16bit timers, two 32bit timers, SSP, I2C.
The kit also integrates a smart and easy-to-use Colink2 JTAG Debugger. It is a good platform for application development and the first choice for learners.
Integrates one LPC1114 Target Board and one smart JTAG Debugger
Brand new, complete functions but very low cost
Features NXP LPC1114FBD48 processor, based on 32bit ARM Cortex-M0, 50MHz
The LPC1114 Starter Kit integrates the NXP LPC1114FBD48 processor which is used high-performance ARM Cortex-M0 32bit RISC kernel, works at up to 50MHz and belongs to the LPC1100 Series Microcontrollers. The LPC1100 Series works in the temperature range from minus 65 Celsius degrees to 150 Celsius degrees, and its power voltage is from 2.0V to 3.6V. The various power saving modes highlight its low power consumption feature.
The comprehensive peripherals of the LPC1114 processor make it suitable for a variety of applications:
Motor driver and application control
PC peripherals
Alarm system
Block Diagram of LPC1114 Kit
USB JTAG Debugger Features
Only support LPC1100 Series currently(Can support other Cortex-M0/M3 MCU later)
Support SW/JTAG debug and Download
Download speed up to 110Kb/s
flexible debugging socket, support 20/10/8 pins connector
Support Keil MDK and CooCox full series software * Debugging conditions: use SW debug, the LPC1114 need to run at 50MHz frequency.
USB JTAG Debugger Features
LPC1114 32bit RISC processor, based on ARM Cortex-M0, 50MHz
Eight LEDS
One Power Indicator
One BOOT Key-press
One RESET Key-press
48pins IO extension One UART, supporting RS-485/EIA-485
SSP Interface
I2C Interface
Eight Channels 10bits ADC Module
One 10pins SWD Debugging Interface
One temperature sensor
LPC1114 Target Board Software Resources
Examples
Descriptions
Blinky
LED1 blinks
GPIO
GPIO interface interrupt trigger
PMU
Power management unit (PMU) sleep and deep sleep mode
SysTick
Implement the LED blink through the system time delay
Timer32
Implement the LED blink through 32bits timer delay
WDT
Watchdog timer application example
SSP
SSP Synchronous Serial Communication
UART
UART interface send/accept character
I2C_EEPROM
I2C main mode to EEPROM read/write test
Temperature Sensor
Read the data of Temperature Sensor through I2C
LPC1114 Starter Kit Standard Configuration
1 x LPC1114LK Development Board
1 x UART DB9 to DIP cable
1 x MINI USB Cable
1 x Serial Port Cable
1 x CD-ROM
There are plenty of documentations and materials in the CD-ROM of this NXP LPC1114 Starter Kitt, such as user’s manual, datasheets, software, example programs, and so on. If you need these materials, please feel free to contact us.
Related documentations
Documentations
Size
Download
NXP LPC1114 Kit User Manual
1.27MB
NXP LPC1114 Kit Schematic
38.6KB
NXP LPC1114 MCU Datasheet
313KB
PACKING LIST
NO
NAME / TYPE
QTY
DESCRIPTION
1
NXP LPC1114 Starter Kit
1
Include a target board and a JTAG Debugger
2
DB9 to IDC10 Pins Cable
1
Connect the debug interface of lpc1114 target board to the COM interface of the PC
3
Mini USB Cable
1
USB-A(M) to Mini-B(M;5pins)
CD-ROM
Including the usermanual, datasheets, software, shematics, etc.
Total weight of each standard package: 1.0 lb.
ORDER INFORMATION
Order#
Descriptions
1
5+
15+
25+
Please contact us for higher volumes
P11L
NXP LPC1114 Starter Kit
$
30
25
20
20
Available.
Note: MOQ 2pcs, that means you are required to purchase at least 2 pieces for each order.
Home 
Products Class
